How to Fix a Broken Charger

Left image
2022-09-19
Jide Mbaka

Whether you're using a device for work or pleasure, a broken charger will disrupt your plans.However, before you go out and buy a new charger, there are a few tricks you can try to fix it. is your  device constantly running out of battery? This might be due to the charger that came with your device not being compatible with your device. Alternatively, your charger could be broken, which means it could be time for a new charger.

To effectively troubleshoot, you simply need to be aware of the most common issues that may arise.Here are some tips to help you repair a broken charger.

Part 1. Reasons for a Charger Failure

There are a few common causes for your charger to stop working:

  1. The wall socket is broken.
  2. A faulty charger.
  3. The device's power port has been damaged.
  4. Your charger may not be properly connected, or it may be too dirty to connect.
  5. However, it is possible that the problem is caused by the power source rather than the charger.

Part 2. How to fix a broken Charger

If your charger isn't working properly, try these fixes.

Step 1. Check the parts of the adapter

Remove the adapter, outlet splitter, power strip, or surge protector, as well as any extra components, so that only the charger is plugged into a known-working outlet. If the outlet works but the charger does not, the issue is not with the wall socket.If the charger works when plugged into a wall outlet, the issue is with one of the removed components. Replace the missing pieces one by one until the system fails, but don't stop there. Try arranging the pieces in a different order or in a different location.

 Step 2. Examine the power outlet

Sometimes the problem is with the outlet, not with the charger. First, you should:Try a different outlet.

  1. If your outlet has one, press the reset button.
  2. Reset a tripped breaker in your fuse box.
  3. Check that the light switch that controls the outlet is turned on.

Step 3. Try a different outlet

 Outlets are strong, but they can fail. Check out our multimeter tips below to ensure an outlet is operational.

Step 4. Examine the Charger for any damage

A bare wire, stripped insulation, or wire shielding could be the source of the issue. Additionally, plug in the cable and wiggle it at both ends. If the charger works intermittently as you move the cable, the copper wiring in the cable has been damaged. Replace the wire with a new one if possible.If there are bare or damaged wires on either end of the cable, do not attempt to wiggle it. This could cause an electric shock.

Check your cable and Charging port

If the cable connections aren't properly connected, they could be the source of the problem.To rule that out and possibly resolve the issue, unplug the cord from both the charging port and the device and then reconnect them.Check to see if the connections are secure and fully connected, and if the problem has been resolved.

IMPORTANT: Frayed cables pose a risk of electrocution, so don't wiggle it around while it's plugged into an outlet. Make sure the cord is unplugged from the wall outlet before applying the tape.

Step 5. Clean the charging port

The charging port should be cleaned. If the charging cable does not connect with a click, look inside the charging device. Users have discovered that anything from pocket lint to a grain of rice caught in the Lightning and USB-C charging ports can prevent the phone from charging. Using plastic tweezers, a cotton swab, or a toothpick, remove any garbage.Never insert anything metal into the charging port. If you insert a piece of metal incorrectly into the charging port, you can short out the connection and destroy the device.

Step 6. Check that the cables are connected properly

Unplug all of the system's cables, wait a few minutes, and then reconnect the cables carefully and properly. When reseating, make sure all of the connections are tight and accurate.

  • Examine the cable for Frays

If your cable is frayed or has exposed wires, it's time to replace it.If you don't have access to a new cable right away, you can cover the fraying area with electrical tape. That should get it working again until you get a new cable.

Step 7. Examine the fuses

 Look for a flipped breaker and flip it back when you open the fuse box. Switches in the same column or row usually point in the same direction. If you see a fuse with its handle pointing in the opposite direction, it has most likely tripped. Locate and reset the fuse associated with the o

utlet you're using. With a springing sound, it springs back into place.

Step 8. Change the cable and power adapter

The charging cable is the most common cause of charger failure. Because the cable is subjected to the most strain over time, it is the first to fail. The charging brick, which connects the wire to the wall, can also fail, though this is less common. Try a different USB charging cable and adapter to see if the problem goes away on its own. To find the culprit, replace one at a time.

Examine the Charger Compatibility

 It's easy to use a physically compatible cable that doesn't fully function. Laptop chargers are more picky, as you can rarely swap one for another without problems. Furthermore, only the proper adapter and cable combination can take advantage of all of the device's features. If you believe you are using an incompatible cable, replace it with one that is compatible with your device.

Step 9. Use a multimeter to check

You can use a multimeter to check the cable and wall outlet for potential problems.

  1. Connect the probes to the multimeter and set it to AC voltage. Insert the black probe into the neutral port and the red probe into the hot or positive side of the outlet to test it. Check the cable if the outlet works.
  2. To test the cable, set the multimeter's central knob to resistance (Ohms, or). Then, using the multimeter's two probes, touch the same pin on opposite ends of the cable. If the multimeter reads zero, the wire is operational. An infinity indicates that the wire is broken and must be repaired or replaced.
  3. Examine the adapter. Plug the adapter into the wall while the multimeter is set to detect AC voltage and inspect the contacts that should be conducting power. If you don't get a measurable voltage from the adapter, it's possible it's not working and you'll need to replace it.
  4. A data cable, such as USB, can only be tested on its two power pins, known as the ground and voltage pins. Examine the connector type's pinout and locate the power-carrying pins (often labeled ground, GND, V+, or 5V) on the diagram.

Conclusion

If you are unable to repair the device, you should contact the manufacturer to discuss your options. If the device is out of warranty or will be too expensive to repair, you may need to purchase a new one.

Do you require additional assistance? Please contact Carlcare.

Whatever the issue is that you cannot handle, book a Carlcare service reservation, and we got you covered. Carlcare is the Offlical after-sales service center for all Infinix, Tecno, Itel, Oraimo and Syinix brands.Carlcare provides support services in the form of professional repair and maintenance service ensuring that your phone is kept in optimal shape while you enjoy using it. You won’t find a better phone support service out there.